HALTECH ECU PRODUCTS

Fuel Injector Adaptor - 14mm 1/2 to Full Length

Fuel Injector Adaptor - 14mm 1/2 to Full Length   Includes: Adaptor, retaining clip and filter basket This fuel injector adaptor allows a 1/2 length (34 mm) injector with 14 mm top O-ring, to be installed as a full-sized (60 mm) injector, fitting a...

Fuel Injector Adaptor - 14mm 3/4 to Full Length

Fuel Injector Adaptor - 14mm 3/4 to Full Length   Includes: Adaptor, retaining clip and filter basket This fuel injector adaptor allows a 3/4 length (48 mm) injector with a 14 mm top O-ring, to be installed as a full-sized (60 mm) injector, fitting...

Fuel Injector Adaptor - 14mm Base

Fuel Injector Adaptor - 14mm Base   This fuel injector adaptor allows a 1/2 length (34 mm) injector with extended tip, 14mm top and bottom O-rings to be installed as a 3/4 length (48 mm) injector.

Fuel Injector Adaptor - Nissan Base

Fuel Injector Adaptor - Nissan Base   This fuel injector adaptor allows a 1/2 length (34 mm) injector with an extended tip, and 14 mm top and bottom O-rings, to be installed into a Nissan intake manifold using a Nissan base O-ring.

Fuel Level Sender Signal Conditioner

Fuel Level Sender Signal Conditioner Outputs: Filters a resistive signal for use with an Analogue Voltage Input (AVI). Includes: HT-031016 - Matching Set of Deutsch DTM 4 Connectors.    

GPS Speed Input Module - Length: 300mm

GPS Speed Input Module Outputs: 0V to 12V Pulsed Output Suits: Apllications that require a digital speed signal Includes: Includes: GPS Speed Input Module & GPS Antenna Matching male DTM-3 Connector and pins Notes: Calibration: 5000ppk (5000 pulses...

GT101 Style High Frequency Hall Effect Sensor - Size: 18mm Diameter

GT101 Style High Frequency Hall Effect Sensor Suits: Wheel Speed, Crank/Cam etc. Includes: Matching set of Deutsch DTM 3 connectors (HT-031014)  

Haltech 1/4" Mild Steel Weld-On Base Only

1/4" Mild steel weld-on base only    

Haltech 1/4" Mild Steel Weld-On Kit

1/4" Mild Steel Weld-on Kit - inc Nut and Ferrule   INCLUDES: Nut and ferrule.   NOTES: Compression ferrules are single use and must be replaced when replacing probes.

Haltech 1/4" Stainless Compression Fitting Kit

1/4" Stainless Compression Fitting Kit - 1/8" NPT Thread   THREAD: 1/8 NPT   INCLUDES: Nut and ferrule.   NOTES: Compression ferrules are single use and must be replaced when replacing probes.

Haltech 1/4" Stainless Steel Weld-On Base Only

1/4" Stainless steel weld-on base only

Haltech 1/4" Stainless Steel Weld-On Kit

1/4" Stainless Steel Weld-on Kit - inc Nut and Ferrule   INCLUDES: Nut and ferrule.   NOTES: Compression ferrules are single use and must be replaced when replacing probes.

Haltech Adaptor - Brass 1/8" NPTF to 3/8" NPTF

Adaptor - Brass 1/8"NPTF to 3/8"NPTF Suits: 1/8" NPT Sensors Includes: Adaptor Only Notes: Tightening Torque: 1.5 - 3 TPFT (Turns past finger tight)    

Haltech CAN Adaptor Cable DTM-4 Female Receptacle/Socket to 8 Pin Black Tyco

Haltech CAN Ada Cable DTM-4 F to 8 pin Black Tyco 75mm (3")   Suits: Used to adapt a Platinum series ECU to Elite DTM-4 CAN system.

Haltech Driveshaft Split Collar - 1.812" / 46mm I.D. 8 Magnet

Haltech Driveshaft Split Collar 1.812" / 46mm I.D. 8 Magnet Includes: 1 x Driveshaft Split Collar 1.812" I.D. 8 Magnet 1 x 5/32 Allen Key Notes: 8 magnet pickup split collar - suits 1.812" / 46mm Driveshaft  

Haltech Driveshaft Split Collar - 1.875"/ 47.63mm I.D. 8 Magnet

Haltech Driveshaft Split Collar 1.875" / 47.63mm I.D. 8 Magnet Includes: 1 x Driveshaft Split Collar 1.875"/ 47.63mm I.D. 8 Magnet 1 x 5/32 Allen Key Notes: 8 magnet pickup collar - suits 1.875"/ 47.63mm Driveshaft      

Haltech Driveshaft Split Collar - 2.125" / 53.98mm I.D. 8 Magnet

Haltech Driveshaft Split Collar 2.125"/ 53.98mm I.D. 8 Magnet Includes: 1 x Driveshaft Split Collar 2.125"/ 53.98mm I.D. 8 Magnet 1 x 5/32 Allen Key Notes: 8 magnet pickup split collar - suits 2.125" / 53.98mm Driveshaft  

Haltech Driveshaft Split Collar - 2.187"\ 55.55mm I.D. 8 Magnet

Haltech Driveshaft Split Collar 2.187" / 55.55mmI.D. 8 Magnet Includes: 1 x Driveshaft Split Collar 2.187"\ 55.55mm I.D. 8 Magnet Notes: 8 magnet pickup split collar - suits 2.187" Driveshaft    

Haltech Elite CAN Cable - DTM4 Receptacle to 16 Pin Black Tyco - Length: 150mm / 6"

Haltech Elite CAN Cable - DTM4 Receptacle to 16 pin Black Tyco - 150mm / 6"   Suits: Compatible Elite 550/750 Plug "n" Play Adaptor harness Includes: 1 x DTM4 Receptacle to Tyco 16 Position Connector  

Haltech Elite CAN Cable DTM-4 to 8 Pin Black Tyco - Length: 1200mm (48")

Haltech Elite CAN Cable DTM-4 - 8 pin Blk Tyco 1200mm (48")

Haltech Elite CAN Cable DTM-4 to 8 Pin Black Tyco - Length: 150mm (6")

Haltech Elite CAN Cable DTM-4 - 8 pin Blk Tyco 150mm (6")

Haltech Elite CAN Cable DTM-4 to 8 Pin Black Tyco - Length: 1800mm (72")

Haltech Elite CAN Cable DTM-4 - 8 pin Black Tyco 1800mm (72")

Haltech Elite CAN Cable DTM-4 to 8 Pin Black Tyco - Length: 300mm (12")

Haltech Elite CAN Cable DTM-4 - 8 pin Blk Tyco 300mm (12")  

Haltech Elite CAN Cable DTM-4 to 8 Pin Black Tyco - Length: 600mm (24")

Haltech Elite CAN Cable DTM-4 - 8 pin Blk Tyco 600mm (24")  

Haltech Elite CAN Cable DTM-4 to 8 Pin Black Tyco - Length: 900mm (36")

Haltech Elite CAN Cable DTM-4 - 8 pin Black Tyco 900mm (36")

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 1200mm (48")

Haltech Elite CAN Cable DTM-4 to DTM-4 1200mm (48") Includes: 1 x DTM-4 to DTM-4 CAN Cable   

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 150mm (6")

Haltech Elite CAN Cable DTM-4 to DTM-4 150mm (6")  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 1800mm (72")

Haltech Elite CAN Cable DTM-4 to DTM-4 1800mm (72")  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 2400mm (92")

Haltech Elite CAN Cable DTM-4 to DTM-4 2400mm (92")  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 3000mm (120")

Haltech Elite CAN Cable DTM-4 to DTM-4 3000mm (120")  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 300mm (12")

Haltech Elite CAN Cable DTM-4 to DTM-4 300mm (12")   Includes: 1 x CAN Connection Cable  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 3600mm (144")

Haltech Elite CAN Cable DTM-4 to DTM-4 3600mm (144")

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 600mm (24")

Haltech Elite CAN Cable DTM-4 to DTM-4 600mm (24")  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 75mm (3")

Haltech Elite CAN Cable DTM-4 to DTM-4 75mm (3")  

Haltech Elite CAN Cable DTM-4 to DTM-4 - Length: 900mm (36")

Haltech Elite CAN Cable DTM-4 to DTM-4 900mm (36")

Haltech Elite CAN Cable DTM-4 to OBDII - Length: 1800mm (72")

Notes: Vehicle side OBDII Connector Connect your Elite ECU to an OBDII Bluetooth or Wireless Module

Haltech HC5 - Hydraulic Crimper

HC5 Hydraulic Crimper 5 TON Suits: 00 AWG to 12AWG cable. Includes: 1 x Hydraulic crimping tool. Rated to 5 Ton. 8 x Die Sets - (Sizes 4,6,10,16,25,35,50,70mm2) 1 x Hydraulic Rebuild Kit 1 x Moulded Carry Case 1 x Quick Start Guide

Haltech iC-7 Colour Display Dash

Suits: All currrent Haltech ECUs via CAN. Also Plug'n'Play compatible with the following aftermarket ECU brands: Link, MaxxECU, Microtech, MoTeC M1 series, MoTeC hundred series- (M400,600,800 gold box ECUs), Syvecs. Includes: Haltech iC-7 Display...

Haltech iC-7 OBD-II Colour Display Dash

SUITS: Preconfigured to connect directly (via CAN) to most late model vehicles (approx 2008-on) using the factory OBD-II port.   INCLUDES: Haltech iC-7 Display Dash, 34 Pin main connector harness (includes spare pins for input wiring), OBD-II to...

Haltech iC-7 OBDII to CAN Cable LENGTH: 1400mm / 55in

LENGTH: 1400mm / 55in   SUITS: Haltech iC-7 Dash   INCLUDES: Cable and Fuse   Haltech Dash to OBD II CAN Cable allows the Haltech iC-7 Dash to display the data obtained from the vehicles OBD II system in real time.